Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
Just how do you really feel about How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately challenging project. If the old bathtub is conveniently easily accessible, the project can relocate rapidly; if you need to open up a wall surface to get rid of the old bathtub as well as place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Make sure you have actually certified on your own for the work as well as fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This write-up will assist you mount a new bath tub in your restroom if you have actually currently gotten a brand-new tub and do not need to transform the plan of your previous water supply pipelines.
Your devices and product checklist must comprise the following:
Preparing for the Setup
Firstly, the supporting frame supplied with the bath needs to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipes. Once the supply pipes have actually been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water system and check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bath tub has actually been used at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Secure the faucet in position with the maker provided backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap adapters. The former kind must be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to break a rigid seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with dampness and possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can split fairly early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is suggested to fit the ceramic tiles making use of waterproof or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting about How to Install a Bathtub when looking around the internet. Do you know another individual who is serious about the topic? Please feel free to share it. Many thanks for taking the time to read it.
Get the best, call! Report this page